INSTRUCTION MANUAL OF R0261P
Plug the AC/DC adaptor to an AC household outlet, and then plug the DC jack to the back of the unit. Your clock radio is ready to work for you.
BACKUP BATTERY INSTALLATION
Your clock radio requires one CR2032 lithium battery (not included) to provide backup power to the clock in the event of a temporary power interruption.
1.Place your unit face down on a flat and soft surface.
2.Slide and remove the battery cover at the bottom of your unit.
3.Insert one new CR2032 lithium battery into the battery compartment with the “+” side facing
up as indicated.
4.Replace the battery cover.
If AC power is interrupted, the LED display will go off and both the radio and the alarm will not function. The backup battery will keep the time and all settings of your unit. Make sure a fresh CR2032 lithium battery is used. A fresh CR2032 battery could backup your clock continuously for around 3 days.
SETTING TIME, 12/24HR TIME AND THE SNOOZE DURATION
1.Press SET once, the hour digits flash. Press or to set the hours. Press and hold
or will accelerate setting at high speed.
2.Press SET again, the minute digits flash. Press or to set the minutes. Press and hold
or will accelerate setting at high speed.
3.Press SET again, the display shows “24Hr” and flashes. Press or to select “12H” or “24H” time format.
4.Press SET again, the display shows “05” and flashes. Press or to select your snooze time from 5 to 60 minutes.
5.Press SET again or if no key pressed for approx. 10 seconds to exit the setting mode.
Note: when 12-hour time format is selected, the PM LED will appear on the lower middle time display to indicate the afternoon time; there is no AM indicator.
SETTING THE ALARMS
1.Press AL 1.2 once, the A1 LED and the hour digits flash. Press or to set the alarm 1 hour. (hold to advance rapidly).
2.Press AL 1.2 again to adjust minutes. Press or to set the alarm 1 minutes. (hold to advance rapidly).
3.Press AL 1.2 again, LED displays “OFF” (alarm off). To select wake to sound sources, press or to select :-
rd = wake-to-radio
bu = wake-to-buzzer
OFF = alarm off
4.Press AL 1.2 again, the A2 LED and the hour digits flash. Press or to set the alarm 2’s hours. Repeat step 2) and 3) to set alarm 2.
5.Press AL1.2 again or no button around 10 seconds to exit alarm setting mode. When wake-to-radio or wake-to-buzzer is selected, the related alarm is turned on, indicated by appearance of the A1 and / or the A2 LED on the left side of the display.
Note: Alarm function just operates with AC/DC adaptor only.
STOPPING AND RESETTING THE ALARM TO COME ON THE NEXT DAY
When alarm 1 or 2 is sounding, the related A1 or A2 LED flashes. Press the RADIO/ SLEEP or AL 1.2 once to stop the alarm and reset it to come on the following day. After that A1 or A2 LED icon keeps on the display.
SNOOZE OPERATION (default snooze duration is 5 minutes)
When alarm is sounding, presses once, the alarm will be silenced and come on again after the set snooze duration.
Note: if your second alarm activates while the first alarm is sounding or it is in the snooze mode, the second alarm overrides the first alarm (the first alarm is reset to come on the next day).
USING THE HI-LO-OFF DIMMER
Press to adjust the brightness (HI/ LO/OFF) of the LED display. This can only be done when the radio is off or the unit is not sounding.
SETTING UP THE FM ANTENNA
Extend the FM wire antenna fully and vary the direction for best FM reception. Do not strip, alter or attach to other antennas.
LISTENING TO THE FM RADIO
1.To turn on the radio, press RADIO/SLEEP once, the display shows “ON” and then the radio frequency readings in Mhz.
2.Press / to tune the radio to a desired station. Press and hold / to scan for the next clear station.
3.To adjust the volume, press VOL once, the display shows “L10”, press / to adjust volume from L01 (minimum) to L15 (maximum).
4.Press to turn off the radio.
Remark: keep your radio away from fluorescent lamps or other electronic devices, which may cause interference to the radio.
USING THE PRESET MEMORY
This clock radio features a total of 10 preset memories of FM stations. These allow you to preset your favorite stations and access them quickly.
1.Turn on the radio and select a radio station you like to memorize.
2.Press and hold the SET until “MEM” LED appears and “01” flashes. Press SET once to store Memory 1.
3.Press or to select another station you like to memorize. Then press and hold SET until “MEM” LED appears and “01” flashes. Press once, “02” appears. Press SET once to store Memory 02.
4.Repeat Step 2 to 3 to preset memories 3 through 10.
5.To access a preset station at any time, press the SET once at a time while the radio is on.
6.To edit a preset station, select another station and then repeat Step 2 to 4. This overrides the original settings.
USING THE SLEEP TIMER
1.Press the RADIO/SLEEP twice to enter the sleep mode. The sleep LED and the sleep time “05” (5 minutes) appear on the display.
2.Press the RADIO/SLEEP again as needed to adjust the sleep timer from 5, 10, 15, 30, 45, 60, 75, 90 or OFF.
3.When the display changes back to show the time, press the RADIO/SLEEP twice to show the sleep time remaining.
4.The radio will play for the programmed sleep time and then shut off.
5.To turn off the radio before the sleep time has elapsed, press once.
TO USE THE PROJECTION (operated by adaptor only)
1.Press once to turn on the projection.
2.Press once again to turn off the projection.
3.When the projection is on, press and hold to flip the projection view upside down. At the back of your unit, use the rotary knob to rotate the projection view by 90 degree.
If your clock displays irrelevant time or does not function properly, which maybe caused by electro-static discharge or other interference, unplug the DC jack to disconnect the AC power (and remove the backup battery). The clock radio will be reset to default settings and you need to set it again.
CARE OF YOUR PRODUCT
1.Place your clock radio on a stable surface, away from sources of direct sunlight or excessive heat or moisture.
2.Protect your furniture when placing your units on a natural wood and lacquered finish by using a cloth or protective material between it and the furniture.
3.Clean your unit with a soft cloth moistened only with mild soap and water. Stronger agents such as Benzene, thinner or similar materials can damage the surface of the unit. Make sure the unit is unplugged before cleaning.
4.If the unit is not to be used for a prolonged period, such as a month or longer, remove the batteries to prevent possible corrosion. Should the battery compartment become corroded or dirty, clean the compartment thoroughly and replace the batteries.
Alarm duration 1 hour
Snooze duration 5 to 60 minutes
Sleep timer selections 5, 10, 15, 30, 45, 60, 75, 90 minutes to OFF
Volume L01 (minimum) to L15 (maximum)
Preset Memories of radio 10
Time format 24 hour
Alarm 1 and 2 6:00
Snooze duration 05 (5 minutes)
Clock decoration very modern desktop clock with alarm and led projection tabletop